SAE AMS 4041P pdf download
SAE AMS 4041P pdf download.Aluminum Alloy,Alclad Sheet and Plate
4.4Cu – 1.5Mg – 0.60Mn Alclad 2024 and 1-1/2%Alclad 2024,-T3 Flat Sheet; 1-1/2% Alclad 2024-T351 Plate.
1.1 Form:
This specification covers an aluminum alloy in the form of sheet and plate clad on both sides with a different aluminum alloy.
1.2 Application:
These products have been used typically for structural components requiring good strength and maximum corrosion resistance, but usage is not limited to such applications. Plate is also suitable for structural machined parts where warpage during machining, due to residual stresses must be minimized.
1.2.1 Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking: ARP823 recommends practices to minimize such conditions.
2. APPLICABLE DOCUMENTS:
The issue of the following documents in effect on the date of the purchase order form a part of this specification to The extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been canceled and no superseding document has been specified, the last published issue of that document shall apply.
2.1 SAE Publications:
Available from SAE, 400 Commonwealth Drive, Warrer’idale, PA 15096-0001.
AMS 2355 Quality Assurance Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products. Except Forging Stock, and Rolled, Forged, or Flash Welded Rings
MAM 2355 Quality Assurance Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded Rings. Metric (SI) Units
AMS 2772 Heat Treatment of Aluminum Alloy Raw Materials
ARP823 Minimizing Stress-Corrosion Cracking in Wrought Heat-Treatable Aluminum Alloy Products
2.2 ASTM Publications:
Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM B 660 Packaging/Packing of Aluminum and Magnesium Products
ASTM B 666’B 666M Identification Marking of Aluminum and Magnesium Products
2.3 ANSI Publications:
Available from ANSI, 11 West 42nd Street, New York, NY 100368002.
ANSI H35.2 Dimensional Tolerances for Aluminum Mill Products
ANSI H35.2M Dimensional Tolerances for Aluminum Mill Products (Metric)
3. TECHNICAL REQUIREMENTS:
3.1 Composition:
Shall conform to the percentages by weight shown in Tables 1 and 2, determined in accordance with AMS 2355 or MAM 2355.
4.2 Classification of Tests:
I4.2.1 Acceptance Tests: Composition (3.1), tensile properties (3.3.1), and tolerances (3.5) are acceptance tests and except for composition, shall be performed on each lot.
4.2.2 Periodic Tests: Bending (3.3.2) and cladding thickness (3.3.3) are periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.
4.3 Sampling and Testing:
Shall be in accordance with AMS 2355 or MAM 2355.
4.4 Reports:
The vendor of product shall furnish with each shipment a report stating that the product conforms to the chemical composition and tolerances and showing the numerical results of tests on each inspection lot to determine conformance to the other acceptance test requirements and, when performed, to the periodic test requirements. This report shall include the purchase order number. Inspection lot number(s), AMS 4041 P. size, and quantity. The report shall also identify the producer, the product form, and the size of the mill product.
4.5 Resampling and Retesting:
Shall be in accordance with AMS 2355 or MAM 2355.
5. PREPARATION FOR DELIVERY:
5.1 Identification:
Shall be in accordance with ASTM B 666B 666M.
5.2 Packaging:
5.2.1 The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery.
5.2.2 Packaging shall be in accordance with ASTM B 660.
6. ACKNOWLEDGMENT:
A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.
