SAE AMS 5529G pdf download

SAE AMS 5529G pdf download.Steel, Corrosion Resistant, Sheet and Strip
17Cr – 7.1Ni – 1.1Al Solution Heat Treated and Cold Rolled,Precipitation Hardenable 0.0015 to 0.050 Inch (0.038 to 1.27 mm) Nominal Thickness.
3.3.2.2 Hardness: Shall be not lower than 46 HRC, or equivalent (See 8.3); for thin gages where superficial hardness testing is impractical, microhardness testing in accordance with ASTM E 384 may be used. Product shall not be rejected on the basis of hardness if the tensile properties of 3.3.2.1 are acceptable, determined on specimens taken from the same sample as that with nonconforming hardness or from another sample with similar nonconforming hardness.
3.4 Quality:
The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product.
3.5 Tolerances:
Shall conform to all applicable requirements of AMS 2242.
4. QUALITY ASSURANCE PROVISIONS:
4.1 Responsibility for Inspection:
The vendor of the product shall supply all samples for vendor’s tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements,
4.2 Classification of Tests:
4.2.1 Acceptance Tests: The following requirements are acceptance tests and shall be performed on each heat or lot, as applicable.
4.2.1.1 Composition (3.1) of each heat.
4.2.1.2 Tensile properties (3.3.1.1 and 3.3.2.1)of each lot.
4.2.1.3 Hardness (3.3.1.2 and 3.3.2.2) of each lot.
4.2.1.4 Tolerances (3.5) of each lot.
4.2.2 Periodic Tests: Freedom from continuous carbide network (3.2.1) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.
4.3 Sampling and Testing:
Shall be in accordance with AMS 2371.
4.4 Reports:
The vendor of the product shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile properties and hardness as cold rolled, and tensile properties and hardness after precipitation heat treatment of each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers. AMS 5529G. size, and quantity.
4.5 Resampling and Testing:
Shall be in accordance weth AMS 2371.
5. PREPARATION FOR DELIVERY:
5.1 Identification:
Shall be in accordance with AMS 2807.
5,2 Packaging:
The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery.
6. ACKNOWLEDGMENT:
A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.
7. REJECTIONS:
Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.
8. NOTES:
8.1 A change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editonal changes only.
8.1.1 This AMS 5529G is an editorial correction necessary to correct publication errors in the F revision. In this instance, the change bar symbol(s) included herein are for the convenience of the user in locating areas where technical changes have been made to the E and F revisions of this specification.