SAE AMS 5606E pdf download
SAE AMS 5606E pdf download.Alloy, Corrosion and Heat-Resistant, Sheet,Strip, and Plate 41.5Ni – 16Cr – 37Fe – 2.9cb – 1.8Ti Consumable Electrode or Vacuum Induction Melted 1750 °F(954 °c) Solution Heat Treated.
2.1 SAE Publications:
Available from SAE International. 400 Commonwealth Dnve, Warrendale, PA 15096-0001, Tel:
877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), wwwsaeorg.
Tolerances, Nickel. Nickel Alloy, and Cobalt Alloy Sheet. Strip, and Plate
Chemical Check Analysis Limits. Nickel, Nickel Alloys and Cobalt Alloys
Quality Assurance Sampling and Testing. Corrosion and Heat-Resistant
Steels and Alloys, Wrought Products and Forging Stock
Identification, Carbon and Low-Alloy Steels, Corrosion and Heat-
Resistant Steels and Alloys. Sheet, Strip, Plate, and Aircraft Tubing
AS 4194 Sheet and Strip Surface Finish Nomenclature
2.2 ASTM Publications:
Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, wwwastm.org.
ASTMA48O!A480M
ASTM E 8
ASTM E 8M
ASTM E 18
ASTM E 112
ASTM E 139
ASTM E 290
ASTM E 354
Flat-Rolled Stainless and Heat-Resisting Steel Plate. Sheet, and Strip
Tension Testing of Metallic Materials
Tension Testing of Metallic Materials (Metnc)
Rockwell Hardness and Rockwell Superficial Hardness of Metallic
Materials
Determining Average Grain Size
Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of
Metallic Materials
Semi-Guided Bend Test for Ductility of Metallic Materials
Chemical Analysis of High-Temperature. Electrical, Magnetic. and
Other Similar Iron. Nickel, and Cobalt Alloys
Microindentation Hardness of Materials
AMS 2262
AMS 2269
AMS 2371
AMS 2807
ASTM E 384
4. QUALITY ASSURANCE PROVISIONS:
4.1 REsponsibility for Inspection:
The vendor of the product shall supply all samples for vendor’s tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements
4.2 Classification of Tests:
All technical requirements are acceptance tests and shall be performed on each heat or lot as applicable.
4.3 Sampling and Testing:
Shall be in accordance with AMS 2371.
4.4 Reports:
The vendor of the product shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile properties, hardness, bending and average grain size as solution heat treated for each lot, and for tensile properties, hardness and stress rupture properties as precipitation heat treated for each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS 5606E, solution heat treatment temperature used, size, and quantity.
4.5 Resampling and Retesting:
Shall be in accordance with AMS 2371.
5. PREPARATION FOR DELIVERY:
5.1 Identification:
Shall be in accordance with AMS 2807.
5.2 Packaging:
The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery.
6. ACKNOWLEDGMENT:
A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.
7. REJECTIONS:
Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.
8. NOTES:
8.1 A change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revisions. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.
8.2 Hardness conversion tables for metals are presented in ASTM E 140.
8.3 Terms used In AMS are clarified in ARP1917.
8,4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary:
dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.
8.5 Purchase documents should specify not less than the following:
AMS 5606E
Form and size of product desired
Quantity of product desired.
8.6 Keywords:
Alloy sheet, strip and plate, corrosion and heat resistant, consumable electrode or vacuum induction melted, UNS N09706.
