SAE AMS 5640T pdf download

SAE AMS 5640T pdf download.Steel, Corrosion-Resistant, Bars, Wire, and Forgings 18cr – 9.0Ni Free Machining.
2. APPLICABLE DOCUMENTS:
The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent speafied herein. The supplier may work to a subsequent revision of a document unless a specific document issue Is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.
2.1 SAE Publications:
Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org.
AMS 2241 Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire
AMS 2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys
AMS 2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys. Wrought Products and Forging Stock
AMS 2374 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steel and Alloy Forgings
AMS 2806 Identification, Bars, Wire, Mechanical Tubing, and Extwsions, Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and Alloys
AMS 2808 Identification, Forgings
2.2 ASTM Publications:
Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or www.astm.org.
ASTM A 370 Mechanical Testing of Steel Products
ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys
3. TECHNICAl.. REQUIREMENTS:
3.1 Composition:
Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods
in accordance with ASTM E 353, by spectrochemical methods, or by other analytical methods
acceptable to purchaser.
5.2 Identification:
Shall be as follows:
5.2.1 Bars and Wire: In accordance with AMS 2806.
5.2.2 Forglngs: In accordance with AMS 2808.
5.2.3 ForgIng Stock: As agreed upon by purchaser and vendor.
5,3 Packaging:
The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and sate delivery.
6. ACKNOWLEDGMENT:
A vendor shall mention this specification number and its revision letter in all quotations and when
acknowledging purchase orders.
7. REJECTIONS:
Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection
8. NOTES:
8.1 A change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revision of the specification. including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial revisions only.
8.1.1 This AMS 5640T is an editorial correction necessary to correct publication errors in the S revision. In this instance, the change bar symbol(s) included herein are for the convenience of the user in locating areas where technical changes have been made to the R and S revisions of this specification.
8.2 Hardness conversion tables for metals are presented in ASTM E 140.
8.3 Terms used in AMS are clarified in ARP1917.
8.4 DImensions and properties in inchlpound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the pflmary units and are presented only for information.
8.5Purchase documents should specify not less than the following:
AMS 5640T
Form and size or part number of product desiredType of product desired
Quantity of product desired.