SAE AMS 5665M pdf download

SAE AMS 5665M pdf download.Nickel Alloy,Corrosion and Heat Resistant, Bars,Forgings,and Rings 74Ni – 15.5Cr – 8.0Fe.
1.1 Form:
This specification covers a corrosion and heat resistant nickel alloy in the form of bars, forgings. flash welded rings, and stock for forging or flash welded rings.
1 .2 Application:
These products have been used typically for parts requiring both corrosion and oxidation resistance and where such parts may require welding during fabrication and for parts requiring oxidation resistance up to 2000 °F (1093 °C) but useful at the higher temperatures only when stresses are low, but usage is not limited to such applications. Strength at elevated temperatures is similar to that of the 18.8 type steels.
2. APPLICABLE DOCUMENTS:
The issue of the following documents in effect on the date of the purchase order form a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been canceled and no superseding document has been specified, the last published issue of that document shall apply.
2.1 SAE Publications:
Available from SAE, 400 Commonwealth Drive, Warrendale. PA 15096-0001.
AMS 2261 Tolerances. Nickel. Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire MAM 2261 Tolerances. Metric. Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire AMS 2269 Chemical Check Analysis Limits. Nickel, Nickel Alloys and Cobalt Alloys AMS 2371 Quality Assurance Sampling and Testing, Corrosion and Heat Resistant Steels and
Alloys, Wrought Products and Forging Stock
3.1.1 Check Analysis: Composition variations shall meet the requirements of AMS 2269.
3.2 Condition:
The product shall be supplied in the following condition:
3.2.1 Bars:
3.2.1.1 Rounds 2.50 Inches (63.5 mm) and Under in Nominal Diameter: Cold drawn unless Ordered hot finished, and turned or ground.
3.2.1.2 Rounds Over 2.50 Inches (63.5 mm) in Nominal Diameter: Hot finished or hot finished and turned or ground.
3.2.1.3 Squares, Hexagons. and Rectangles: Hot finished.
3.2.2 Forgings and Flash Welded Rings: Annealed.
3.2.2.1 Flash welded rings shall not be supplied unless specified or permitted on purchasers part drawing. When supplied, rings shall be manufactured In accordance with AMS 7490.
3.2.3 Stock for Forging or Flash Welded Rings: As ordered by the forging or flash welded ring manufacturer.
3.3 Properties:
The product shall conform to the following requirements.
3.3.1 Bars, Forgings, and Flash Welded Rings:
3.3.1.1 Tensile Properties: Shall be as shown in Table 2, determined in accordance with ASTM E 8 or ASTM E SM on specimens taken from round bars over 2.50 to 4.50 inches (over 63.5 to 114.3 mm), inclusive, in nominal diameter and from forgings over 2.50 inches (63.5 mm) In nominal thickness.
4. QUALITY ASSURANCE PROVISIONS:
Responsibility for Inspection:
The vendor of the product shall supply all samples for vendor’s tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements.
4.2 Classification of Tests:
4.2.1 Acceptance Tests: Composition (3.1), tensile properties (3.3.1.1), hardness (3.31.2) and tolerances (3.5) are acceptance tests and shall be performed on each heat or lot as applicable.
4,2.2 Periodic Tests: Grain flow of die forgings (3.4.1) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.
4.3 Sampling and Testing:
Shall be as follows:
4.3.1 Bars, Flash Welded Rings, and Stock for Forging or Flash Welded Rings: In accordance with AMS 2371.
4.3.2 Forgings: In accordance with AMS 2374.
4.4 Reports:
4.4.1 The vendor of product shall furnish with each shipment a report of the chemical composition of each heat and the condition, hardness and tensile properties when applicable of each lot and stating that the poduct conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers. AMS 5665M. size and quantity. If forgings are supplied, the size and melt source of stock used to make the forgings shall also be included.
4.5 Resampling and Retesting:
Shall be as follows:
4.5.1 Bars, Flash Welded Rings, and Stock for Forging or Flash Welded Rings: In accordance with AMS 2371.