SAE AS 40401 pdf download

SAE AS 40401 pdf download.Solenoid,Electrical,General Specification For.
This specification covers the general requirements for electrical solenoids used to actuate variousdevices through the conversion of electrical signals into mechanical motion.These solenoids are ofthe axial stroke type and the rotary stroke type.
1.2Classification:
Solenoids are classified as follows:
2. APPLICABLE DOCUMENTS:2.1Government documents:
2.1.1 Specifications, standards, and handbooks: The following specifications,standards, and
handbooks form a part of this document to the extent specified herein. Unless otherwise specified,the issues of these documents are those listed in the issue of the Department of Defense Index ofSpecifications and Standards(DODISS) and supplement thereto.
SPECIFICATIONS
FEDERAL
Q-c-320 – Chromium Plating (Electrodeposited).QQ-N-290 -Nickel Plating (Electrodeposited).
QQ-S-365 – Silver Plating,Electrodeposited,General Requirements for.
2.1.1 (Continued):
STANDARDS
MILITARY
MIL-STD-202 -Test Methods for Electronic and Electrical Component Parts. MIL-STD-1285- Marking of Electrical and Electronic Parts.
(Unless otherwise indicated, copies of federal and military specifications, standards, and
handbooks are available from the Defense Printing Service Detachment Office, Building 4D
(Customer Service), 700 Robbins Avenue, Philadelphia, PA 19111 -5094.)
2.2 Non-Government publications:
The following document forms a part of this document to the extent specified herein. If the document is DoD adopted, the issue is that listed in the issue of the DODISS cited in the solicitation.
AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)
ANSI.’NCSL 2540-1 – Calibration Laboratories and Measuring and Testing Equipment – General Requirements.
(Application for copies should be addressed to American National Standards Institute (ANSI), 11 West 42nd Street, New York, NY 10036.
AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
ASTM B633 – Zinc on Iron and Steel, Electrodeposited Coatings of.
(Application for copies should be addressed to American Society for Testing and Materials (ASTM), 1916 Race Street, Philadelphia, PA 19103.)
INTERNATIONAL ORGANIZATION FOR STANDARDS (ISO)
ISO 10012-1 – Quality Assurance Requirements for Measuring Equipment – Part 1: Metrological Confirmation System for Measuring Equipment.
(Application for copies should be addressed to American National Standards Institute (ANSI), 11 West 42nd Street, New York, NY 10036.
(Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.)
2.3 Order of precedence:
In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
3. REQUIREMENTS:
3.1 Product specifications or engineering drawings:
The individual item requirements shall be as specified herein and in accordance with the applicable product specification or engineering drawing. In the event of a conflict between the requirements of this specification and the product specification or engineering drawing, the latter shall govern.
3.2 First article inspection:
When specified, samples shall be subjected to first article inspection (see 6.2) in accordance with
4.5.
3.3 Materials:
The materials shall be as specified herein. When a definite material is not specified, a suitable material shall be used which will enable the solenoids to meet the perfomiance requirements of this specification. Acceptance or approval of any constituent material shall not be construed as a guaranty of acceptance of the finished product.
3.3.1 Fungus resistant materials: Nonmetallic parts of the solenoid shall be inherently nonfungus nutrient or treated to resist fungus growth.
3.3.2 Metals: Metals shall be of a corrosion resistant type. or shall be plated or treated to resist corrosion.
3.3.2.1 Dissimilar metals: When dissimilar metals are used in intimate contact with each other. protection against electrolysis and corrosion shall be provided. The use of dissimilar metals n contact, which tend toward active electrolytic corrosion (particularly brass, copper, or steel used In contact with aluminum or aluminum alloy). is not acceptable. However, metal plating or metal spraying of dissimilar base metals to provide suitable abutting surfaces is permitted. A list of materials is included in 6.3.
3.3.3 Plastic: Plastic material shall be of a type that will enable the solenoid to meet all the performance requirements of this specification.